Engineering Equipment

Product Details:

To conduct the experiment of Hydraulic Bench Apparatus with separate experiential set ups i.e. Hydrostatic Pressure, Flow over Weirs, Bernoulli’s Theorem, Flow meter Demonstration, Impact of jet and Orifice Discharge etc. which are accessories of the Hydraulic Bench.

Product Details:

• The set up is a self-contained, water recirculation unit provided with a top tray, sump tank and a measuring tank.
• Drain valve and over-flow are provided on the sump tank. A centrifugal pump is fitted for water circulation. 
• Flow control valve and bypass valve is fitted in water line to conduct the experiment at different flow rates.
• Flow rate of water is measured with the help of measuring tank and stop watch. 
• Measuring tank is provided to measure the discharge. Drain valve is provided in the measuring tank to empty water in sump tank after measuring discharge.
• Separate level indicator and scale is provided to read the level of water in the measuring tank.

Product Details:

Steam Power Plant Working Unit – This Unit Helps The Students To Understand The Complete System Of A Thermal Power Plat. Heat Energy Converts Water Into SteamSteam Pressure When Moves A Engine Or Turbine Produces Mechanical Energy Finally Mechanical Energy Is Converted Into Electricity Through Alternator.

Product Details:

The apparatus consists of a variable speed D.C. Motor, Driving pulley and Driven pulley of equal diameter. The pulleys are mounted on input shaft (Motor shaft) and output shaft. The driven pulley can slide on the base with bearing block to change initial tension in belt. Brake drum is mounted on output shaft helps to measure power output. The motor speed is varied by dimmerstat. A two channel RPM Indicator is provided to measure speeds of driven and driving pullies respectively.

Product Details:

The unit consists of ducting fitted with various air conditioning components. Airflow is generated by an axial flow fan and in the airflow, heaters, cooling coil and steam humidifier connection is provided. Cooling circuit consists of a hermetic compressor; air cooled condenser, thermostatic expansion valve and evaporator (i.e. cooling coil). Measurements of various parameters Torn cooling cycle and heating cycle are provided and students can easily visualize and understand the basic principles of air conditioning.

Product Details:

The apparatus consists of a Water Cooler Trainer embraced by evaporator coil of the cooling unit, cooling cycle comprises of a hermetically sealed compressor, air-cooled condenser, a capillary tube as expansion device and an evaporator cell. The stainless steel water tank is provided with insulation on air Sides and a door are provided at the top. Cold water can be taken out from a top provided and inlet water supply is controlled by a bail-operated top. Various measurements provided enable students to determine the theoretical and actual COP, power consumption, actual cooling capacity refrigerant flow and compressor volumetric efficiency of compressor.

Product Details:

The unit consists of vapor compression refrigeration cycle provided with components normally used in refrigeration system so that student can get familiar with the components. Various measurement provided enable students to estimate the performance of the system.

Product Details:

We offer wide range of equipment for Thermodynamics Laboratory. Our product range include Steam Calorimeter, Gas Calorimeters & apparatus to test fuel properties. Our products are manufactured using premium quality raw material. All the equipment confirm with applicable IP / ASTM / IS Standards.

Additional Information:

• Production Capacity: 100
• Delivery Time: 10 days
• Packaging Details: In Box

Product Details:

The Air Conditioning Equipment Test Rig unit is required to conduct experiments and demonstrate the process of cooling of atmospheric air.

The self contained unit will be fitted with all of  instruments facilities so that is temperature, pressure etc. may be measured at different points in the air conditioning system.

Additional Information:

• Production Capacity: 100
• Delivery Time: 10 days
• Packaging Details: In Box

Product Details:

We have Theory of Machine Lab Equipments available with us.

Product Details:

The Set-up consists of a bend and elbow, a sudden expansion & sudden contraction fitting from, ball valve and gate valve. Pressure tapings are provided at inlet and outlet of these fittings under test. A differential manometer fitted in the line gives pressure loss of individual fitting. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

Product Details:

The apparatus consists of a copper bar, which is heated at one end, a heat sink is provided at other end. The test section of bar is properly insulated and thermocouples are attached along the length of bar. Heat conducted through the section of bar is measured by heat collection in water-cooled heat sink.

Product Details:

This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.

Product Details:

Features:

• Hook Gauges
• Venturimeters & Orificemeters
• Manometers
• Pitot Tube
• U Tube Double Column Manometer
• Differential Manometer
• Inclined Manometer
• Valves Models
• Hydraulic Non Return Valve
• Gate Valve
• Globe Valve
• Turbines & Pumps Models

Product Details:

The Set-up is designed to verify Bernoullis Theorem Apparatus experimentally. Set up consists of a one piece clear acrylic test section with convergent and divergent part section, supply tank, measuring tank, inlet water tank and pump for closed loop water circulation. The test section is connected to Piezometer tubes through pressure tapping at different locations on the section to demonstrate the Bernoulli’s Theorem. The flow rate of water is measured using measuring tank and stop watch provided.

Product Details:

The test rig comprises of a two-stage air compressor fitted with an air tank with orifice, pressure gauges 9 an energy meter to measure the input & a Temperature indicator measures the temperatures at various points. The compressor is mounted on air receiver along with the motor, and is provided with air relief valve (safety) and a pressure switch. The unit determines volumetric efficiency and isothermal efficiency at various discharge pressures. 

Product Details:

This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.

Product Details:

The apparatus consists of a plain steel shaft encased in a bearing and directly driven by a small electric motor. The bearing is freely supported on the shaft and sealed at motor end. The motor speed is precisely controlled by control unit and sealed at motor end. The motor speed is precisely controlled by control unit and can be run in both directions. The bearing contains twelve equi-spaced pressures tapping around circumference and four along the axis. All are connected by light flexible plastic tube to the manometer so that the pressure head of all sixteen point can be observed at a time. The bearing can be loaded by attaching weight to the arm supported beneath it.

Product Details:

The apparatus is designed to study the cam profiles and performance of cam and follower system. The apparatus consists of a shaft supported by ball bearings upon which three different types of cams can be mounted. The push rod for follower is supported vertically, which can adopt three different types of followers. Cams and followers can be changed easily. A variable speed motor rotates the cam. A dial gauge permits plotting of follower displacement with respect to cam position. By operating the system at different Speeds, jump speed can be found and also the effect of weight and spring force on jump speed can be studied. Jump can be visualized also with the help of stroboscope (supplied extra).

Product Details:

The unit consists of a main spindle driven by a variable speed motor. Three different governor assemblies can be mounted over the spindle. A with pointer measures the lift of the governor. Students can calculate characteristics of governor at and compare their performance viz. Sensitiveness, stability, governor effort etc.

Product Details:

The rotor is connected to the variable speed motor. The weight of the motor is balanced by another weight, which is on either side of the rotor. By putting weights on the weight platform torque can be supplied to rotor, which is also called gyroscopic couple.

This rotor is free to rotate about:

• Its own axis i.e. axis of spin.
• Axis of precession.
• Axis of gyroscopic couple.

Product Details:

The unit consists of a vertical brass pipe heated by a cartridge heater inside it. The pipe looses heat to atmosphere by natural convection. It is fitted in an enclosure to provide undisturbed natural convection currents. Thermocouples are attached on the pipe to measure local temperatures. Heater input is measured on voltmeter and ammeter. Thus students can determine overall heat transfer coefficient and local transfer coefficients in natural convection at various heat transfer rates.

Product Details:

The unit consists of a circular pipe; loosing heat by forced convection to air, being forced through it. Constant heat flux is added to pipe by an electrical heater, provided with input control. The pipe surface temperature is measured at various points along length of pipe. Temperature of air at inlet and outlet of test section are measured. Thus the students can calculate local and overall heat transfer coefficients in forced convection, at various airflow rates and various heat flux values.

Product Details:

Heat Transfer Through Lagged PipeShell & Tube Heat ExchangerHeat Pipe DemonstratorThermal Conductivity Of Insulating Powder ApparatusThermal Conductivity Of Metal Rod ApparatusThermal Conductivity of Insulating Slab ApparatusThermal Conductivity of Liquids ApparatusEmissivity Measurement ApparatusDropwise Filmwise Condensation ApparatusHelical Coil ApparatusHeat Transfer Through Composite WallsParallel Counter Flow Heat Exchanger Heat Transfer In Forced ConvectionStefan Boltzman ApparatusUnsteady State Heat Transfer Unit

Additional Information:

• Production Capacity: 100
• Delivery Time: 10 Days
• Packaging Details: In Box

Product Details:

Fluid Mechanics Lab Equipment Flow Through Orifice and Mouthpiece Pitot Tube Setup Reynold Apparatus Jet Pump Test Rig Flow Over Notch Metacentric Heightbernoull''s Theorem Apparatus Venturi Meter And Orifice Meter Apparatus Impact Of Jet Of Vane.

Additional Information:

• Production Capacity: 1000
• Delivery Time: 10 days
• Packaging Details: In Box